Acerca de este Programa Especializado
Cursos 100 % en línea

Cursos 100 % en línea

Comienza de inmediato y aprende a tu propio ritmo.
Cronograma flexible

Cronograma flexible

Establece y mantén fechas de entrega flexibles.
Nivel intermedio

Nivel intermedio

Recommended: 4-year degree in electrical/mechanical engineering; analog and digital circuit design and circuit analysis; digital oscilloscope

Horas para completar

Aprox. 3 meses para completar

Sugerido 7 horas/semana
Idiomas disponibles

Inglés (English)

Subtítulos: Inglés (English)...

Qué aprenderás

  • Check

    Study a lab experiment or production process and understand how to specify the proper sensor solution for taking real-time process data

  • Check

    Implement the sensor into an embedded system in both hardware and software

  • Check

    Modify existing hardware schematic to add sensors and all support circuitry needed to implement the signal chain in existing microprocessor system

  • Check

    Create hardware and firmware to process the sensor signal and feed data to a microprocessor for further evaluation

Habilidades que obtendrás

sensor integrationfirmwaremotor designembedded engineeringhardware
Cursos 100 % en línea

Cursos 100 % en línea

Comienza de inmediato y aprende a tu propio ritmo.
Cronograma flexible

Cronograma flexible

Establece y mantén fechas de entrega flexibles.
Nivel intermedio

Nivel intermedio

Recommended: 4-year degree in electrical/mechanical engineering; analog and digital circuit design and circuit analysis; digital oscilloscope

Horas para completar

Aprox. 3 meses para completar

Sugerido 7 horas/semana
Idiomas disponibles

Inglés (English)

Subtítulos: Inglés (English)...

Cómo funciona Programa Especializado

Toma cursos

Un programa especializado de Coursera es un conjunto de cursos que te ayudan a dominar una aptitud. Para comenzar, inscríbete en el programa especializado directamente o échale un vistazo a sus cursos y elige uno con el que te gustaría comenzar. Al suscribirte a un curso que forme parte de un programa especializado, quedarás suscrito de manera automática al programa especializado completo. Puedes completar solo un curso: puedes pausar tu aprendizaje o cancelar tu suscripción en cualquier momento. Visita el panel principal del estudiante para realizar un seguimiento de tus inscripciones a cursos y tu progreso.

Proyecto práctico

Cada programa especializado incluye un proyecto práctico. Necesitarás completar correctamente el proyecto para completar el programa especializado y obtener tu certificado. Si el programa especializado incluye un curso separado para el proyecto práctico, necesitarás completar cada uno de los otros cursos antes de poder comenzarlo.

Obtén un certificado

Cuando completes todos los cursos y el proyecto práctico, obtendrás un Certificado que puedes compartir con posibles empleadores y tu red profesional.

how it works

Hay 4 cursos en este Programa Especializado

Curso1

Sensors and Sensor Circuit Design

4.3
24 calificaciones
3 revisiones
After taking this course, you will be able to: ● Understand how to specify the proper thermal, flow, or rotary sensor for taking real-time process data. ● Implement thermal sensors into an embedded system in both hardware and software. ● Add the sensor and sensor interface into a microprocessor based development kit. ● Create hardware and firmware to process sensor signals and feed data to a microprocessor for further evaluation. ● Study sensor signal noise and apply proper hardware techniques to reduce it to acceptable levels. You will need to buy the following components to do the two course projects based on the videos in this module. Note that if you have already purchased the PSOC 5LP PROTOTYPING KIT, you do not need to buy it again. These parts may be purchased off the Digikey web site, www. Digikey.com. Or, you may obtain the specs from the site, and purchase them elsewhere. These are the part numbers typed out, so you can copy and paste them into the Digikey web site. You will need one of each part. 428-3390-ND NHD-0216BZ-RN-YBW-ND 570-1229-ND A105970CT-ND...
Curso2

Motors and Motor Control Circuits

4.1
16 calificaciones
3 revisiones
This is our second course in our specialization on Embedding Sensor and Motors. To get the most out of this course, you should first take our first course entitled Sensors and Sensor Circuits. Our first course gives you a tutorial on how to use the hardware and software development kit we have chosen for the lab exercises. This second course assumes that you already know how to use the kit. After taking this course, you will be able to: ● Understand how to specify the proper AC or DC motor for a machine design. ● Integrate the motor to a machine, based on analysis of motor equations for voltage, current, torque and speed. ● Implement the motor and accompanying rotary sensor into a motor control circuit in both hardware and software. ● Add a motor and motor control circuit into a microprocessor based development kit. ● Create hardware and firmware to process motor feedback data to a microprocessor for further evaluation. You will need to buy the following components to do the two course projects based on the videos in this module. Note that if you have already purchased the PSOC 5LP PROTOTYPING KIT, you do not need to buy it again. These parts may be purchased off the Digikey web site, www. Digikey.com. Or, you may obtain the specs from the site, and purchase them elsewhere. These are the part numbers for the above table, the lab on Motor Voltage and Current Measurement. You can copy and paste them into the search engine on the Digikey web site. You need one of each except for the AA batteries (N107-ND), which you would need 3. 428-3390-ND P14355-ND FQU13N10LTU-ND N107-ND 1N5393-E3/54GICT-ND RNF14FTD1K00CT-ND P0.62W-1BK-ND These are the part numbers for the above table, so you can copy and paste them into the search engine on the Digikey web site. You will need one of each. 428-3390-ND 987-1188-ND...
Curso3

Pressure, Force, Motion, and Humidity Sensors

3.7
3 calificaciones
1 revisiones
After taking this course, you will be able to: ● Understand how to specify the proper pressure, force, strain, position, motion, acceleration, occupancy, and humidity sensors for taking real-time process data. ● Implement these sensors into an embedded system in both hardware and software. ● Add the sensor and sensor interface into a microprocessor based development kit. ● Create hardware and firmware to process sensor signals and feed data to a microprocessor for further evaluation. In this course you will build the circuit from Video 7 (Lab Exercise on strain gauges), Module 2 (Force and Strain Sensors and Touch Screens), and use it to make screen shots of the timing of the switch. If you haven't already wired up the system and written all the software per the instructions of Video 7, please do so now. You will need to buy the following components to complete this assignment. Note that if you have already purchased the PSOC 5LP PROTOTYPING KIT, you do not need to buy it again. These parts may be purchased off the Digikey web site, www. Digikey.com. One part needs to be purchased off the Sparkfun website www.sparkfun.com. Or, you may obtain the specs from the site, and purchase them elsewhere. Digikey Part numbers are typed out here: 428-3390-ND CF14JT22K0CT-ND CF14JT100KCT-ND Table shown here: Index Quantity Part Number Description 1 1 428-3390-ND PSOC 5LP PROTOTYPING KIT 2 2 CF14JT22K0CT-ND RES 22K OHM 1/4W 5% AXIAL 3 1 CF14JT100KCT-ND RES 100K OHM 1/4W 5% AXIAL Sparkfun part numbers are typed out here: TAL221 Table shown here: Index Quantity Part Number Description 1 1 TAL221 Mini-load cell - 100g, straight bar...
Curso4

Sensors and PID Control

You will learn about sensor signal characterization and manufacturing techniques and how to optimize the accuracy of sensors. You will also learn about more advanced sensors, proportional-integral-derivative (PID) control, and how this method is used to give you a closed loop sensor feedback system....

Instructores

Avatar

James Zweighaft

Instructor
Electrical, Computer & Energy Engineering
Avatar

Jay Mendelson

Instructor
Electrical, Computer & Energy Engineering

Acerca de Universidad de Colorado en Boulder

CU-Boulder is a dynamic community of scholars and learners on one of the most spectacular college campuses in the country. As one of 34 U.S. public institutions in the prestigious Association of American Universities (AAU), we have a proud tradition of academic excellence, with five Nobel laureates and more than 50 members of prestigious academic academies....

Preguntas Frecuentes

  • ¡Sí! Para empezar, haz clic en la tarjeta del curso que te interesa e inscríbete. Puedes inscribirte y completar el curso para obtener un certificado que puedes compartir o puedes acceder al curso como oyente para ver los materiales del curso de manera gratuita. Cuando cancelas la suscripción de un curso que forma parte de un programa especializado, se cancela automáticamente la suscripción de todo el programa especializado. Visita el panel del estudiante para realizar un seguimiento de tu progreso.

  • Este curso es completamente en línea, de modo que no necesitas ir a un aula en persona. Puedes acceder a tus lecciones, lecturas y tareas en cualquier momento y cualquier lugar a través de Internet o tu dispositivo móvil.

  • Este programa especializado no otorga crédito universitario, pero algunas universidades pueden aceptar los Certificados del programa especializado para el crédito. Consulta con tu institución para obtener más información.

¿Tienes más preguntas? Visita el Centro de Ayuda al Alumno.